How To Clean Directv Rc64rb Remote Control Buttons

Is your DIRECTV remote not responding? Information technology happens to everyone. Maybe information technology got dropped one too many times, or maybe you're trying to employ an onetime remote with a new box. Either way, you may need to reset information technology. No matter which remote you take, every bit long as it has a DIRECTV logo on it at that place's a very easy way to reset it.

Start things first: supercede the batteries

Dead or weak batteries are nearly always the problem with remotes. Even if the remote is working some of the fourth dimension, modify the batteries earlier doing annihilation else. Weak batteries tin can cause poor signals that cause problems. Put in a fresh pair of batteries. Trust me, you'll be glad you lot did.

How to reset the old-school white remote

Does your remote look similar the one above? This remote was included with every DIRECTV box from 2003 until 2014 and is still included with some DIRECTV boxes today. It'due south easy to reset.

If you are able to use the front panel of your receiver:

Printing MENU then arrow down to Settings&Help and press SELECT.
Then arrow over to Settings and press SELECT again.
Finally, arrow downwards to Remote Control and printing SELECT.
Make sure Reset Remote is highlighted. Printing SELECT.
Depending on your setup, this may be automated or you may accept to enter codes into your remote.

If yous tin't control the receiver at all, here'southward the transmission method.

On the remote, Printing and hold MUTE and SELECT at the same fourth dimension until the light flashes iii times. Then printing Press 9 eight 1 and SELECT. The remote will flash four times and should now exist reset.

RF remotes

If you accept set the receiver to RF mode, you will have to change it to IR fashion or fix the remote dorsum to RF style. There's a comprehensive tutorial here, but here'southward the easy version:

Make sure the top slider is in the DIRECTV mode (far left.)
Press and holdMUTE andSELECT until the low-cal on the remote flashes twice.
And then printing 9 6 oneand press theAqueduct UP push.
Enter the terminal six digits of your receiver ID and pressSELECT.(This is on a light-green sticker on the receiver or you lot tin get it from your "My Equipment" page at DIRECTV.com.
PressSELECT one more fourth dimension.

If yous demand to modify other settings that are specific to the receiver, like the receiver style (for example, if the receiver is set to one of the "other modes" that allow more than than one receiver to be used in the same room, you should now exist able to apply your remote to become into the programming and advanced menus on the receiver.

Genie Remotes

If your remote looks similar this, the process is similar. This remote is standard for all Genie hardware made since 2014. Nearly Genie devices don't have front panel buttons, so you can't go that route. If you are able to apply your remote at all, you tin try the menus. Sometimes holding information technology very close to the DIRECTV box can help.

Press Menu then pointer down to Settings.
Then arrow over to Remote Control and printing SELECT.
Pointer downward to Program Remote and printingSELECT.
Make sure Reset Remote is highlighted. Press SELECT.
Depending on your setup, this may be automatic or yous may have to enter codes into your remote.

If y'all can't control the receiver at all, the transmission method is the same as the other style of remote:

On the remote, Printing and concur MUTE and SELECT at the same time until the calorie-free flashes 3 times. And then printing Press 9 8 1 and SELECT. The remote will flash four times and should now be reset.

Programming for RF

Programming the Genie remote for RF is much, much easier. Get-go, make sure the Genie box is on. Then hold downwardly MUTE andENTER at the same time while pointing the remote at the Genie box. Remember, that's the ENTER button to the right of the zero, not the SELECT push button. You should get a message that the remote is now set for RF.

If yous accept other settings similar Idiot box volume, you should now be able to program them through the menus.